Support A2Billing :

provided by Star2Billing S.L.

Support A2Billing :
It is currently Thu Mar 28, 2024 5:45 pm
Hosted Voice Broadcast


All times are UTC




Post new topic Reply to topic  [ 5 posts ] 
Author Message
 Post subject: ONNET CALLING
PostPosted: Fri Aug 19, 2011 9:28 am 
Offline

Joined: Thu Aug 18, 2011 3:27 pm
Posts: 4
hie

l have setup a2billing 1.7 and asterisk 1.6.l can make outbound calls but challenge is on onnet calls and the billing.
1.Can you please give me a step by step on how l set up onnet calling from creating the trunks,providers,rates etc
2.setting up INBOUND calling .


Top
 Profile  
 
 Post subject: Re: ONNET CALLING
PostPosted: Fri Aug 19, 2011 11:19 am 
Offline

Joined: Fri Jun 23, 2006 3:56 pm
Posts: 4065
Hi

Calls from one customer to another customer's DID are handled within the platform, and do not go out to a trunk, therefore simply set up DID, you can also set a simple cost to call another customer's DID.

Joe


Top
 Profile  
 
 Post subject: Re: ONNET CALLING
PostPosted: Fri Aug 19, 2011 2:31 pm 
Offline

Joined: Thu Aug 18, 2011 3:27 pm
Posts: 4
hie

l think that is where my major challenge is l have created the customers and all the required configs pertaining to the customers and the voip settings, as well as the inbound destinations.do u mean that l dont change any configs on the system in relation to the onnet calling.l also want to be able to bill these calls when the customers call each other how do l go about it.l tried adding the rate of the onnet calls and there is a part where am supposed to enter the trunk,provider ip,how do l bppass that.


thak you


Top
 Profile  
 
 Post subject: Re: ONNET CALLING
PostPosted: Fri Aug 19, 2011 3:39 pm 
Offline

Joined: Fri Jun 23, 2006 3:56 pm
Posts: 4065
Hi

As explained above, On Net calling in A2Billing is achieved using the DID functionality.

Simply create a DID, a DID destination to your customers endpoints, and you have on net calling with billing.

Joe


Top
 Profile  
 
 Post subject: Re: ONNET CALLING
PostPosted: Wed Aug 20, 2014 11:34 am 
Offline

Joined: Fri Aug 15, 2014 2:24 pm
Posts: 2
Hi Guys

This topic is really old, but I've run out of ideas. I've posted something on this forum last week, here is the link:

viewtopic.php?f=9&t=10905

But I've included the contents here anyway:
------------------------------------------------------------------------------------------------------
Hi Guys

Hoping someone can give me a hand here.

I have Elastix 2.4.0 setup and comes with A2billing 1.9.4 installed. I have everything set up, well almost everything. Outbound calls work perfectly as well as inbound calls. I have set up a few DID with my provider. Those DID are set up on my A2B system and are forwarding calls in the following format to a hosted PBX (FreePBX):

SIP/[email protected]

On the hosted FreePBX I have set up the inbound routes, which forward the calls to extensions or ring groups. All working fine.

My question is this.

I have 2 clients currently on this A2B system. Both have DID's assigned to their accounts and both have hosted PBX's. When the one client calls the other via their DID, the call starts off as a DID_VOIP in the CDR's and then goes out via a trunk to the VOIP provider only to come back in again via the inbound routes.

I want to allow the calls to stay within my A2B and have searched this forum and many others without any solution.

Here is a screenshot of the CDR record where you can see the call as a DID_VOIP call and then goes out and is billed:

Image

I'm thinking it has something to do with the context's so here is what is listed in my extension_a2billing_additional.conf:

[a2billing]
include => a2billing_callingcard
include => a2billing_monitoring
include => a2billing_voucher
include => a2billing_did

[a2billing_callingcard]
; CallingCard application
exten => _X.,1,NoOp(A2Billing Start)
exten => _X.,n,DeadAgi(a2billing.php,1)
exten => _X.,n,Hangup

[a2billing_voucher]
exten => _X.,1,Answer(1)
exten => _X.,n,DeadAgi(a2billing.php,1,voucher)
;exten => _X.,n,AGI(a2billing.php,1,voucher,44) ; will add 44 in front of the callerID for the CID authentication
exten => _X.,n,Hangup

[a2billing_did]
exten => _X.,1,DeadAgi(a2billing.php,1,did)
exten => _X.,2,Hangup

In Elastix, I have a custom desitnation setup for all the above, the inbound route in Elastix is set up to forward all inbound calls to [a2billing_did] custom destination.

My context for all customers in A2Billing is the default of A2BILLING.

Any help would be great.

Many thanks
Vince


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 
Hosted Voice Broadcast


All times are UTC


Who is online

Users browsing this forum: No registered users and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group